Views
2 years ago

Sensys Manual - Ariston

  • Text
  • Instructions
  • Manual
  • Control
  • Sensys
  • Programming
  • Display
  • Parameter
  • Boiler
  • Settings
  • Heating
  • Sensor

GB table of error codes

GB table of error codes ERROR DESCRIPTION Servicing scheduled 3 P9 Call Service Centre 3 08 ATM config. error 3 09 Gas relay error 3 11 Boiler error 3 12 Boiler error 4 01 Mdm-Bus com. err. 4 02 GPRS mdm error 4 03 Sim Card error 4 04 Mdm-P.C.B. com. err. 4 05 Mdm In1 error 4 06 Mdm In2 error 4 11 Z1 room sensor not available 4 12 Z2 room sensor not available 4 13 Z3 room sensor not available 4 14 Z4 room sensor not available 4 15 Z5 room sensor not available 4 16 Z6 room sensor not available 4 20 Bus power supply overload (*) 4 21 Boiler error 4 22 Boiler error 5 01 No flame 5 02 Flame without gas 5 04 Flame cut-off 5 P1 1 failed ignition 5 P2 2 failed ignition 5 P3 Flame cut-off 5 P4 Flame cut-off 5 10 Boiler error 5 11 6 01 Flue gas sensor err. 6 02 ERROR DESCRIPTION 6 04 Low fan speed 6 05 Faulty flue gas sensor 6 07 Press. switch ON fan OFF 6 08 Press. switch OFF fan ON 6 09 Flue gas overheat 6 10 Exchange sensor open 6 12 Fan error 6 P1 Flue gas press. delay 6 P2 Flue gas press. opening 6 P4 Low fan speed 6 20 Boiler error 6 21 Boiler error 7 01 Faulty Z1 flow sensor 7 02 Faulty Z2 flow sensor 7 03 Faulty Z3 flow sensor 7 04 Faulty Z4 flow sensor 7 05 Faulty Z5 flow sensor 7 06 Faulty Z6 flow sensor 7 11 Faulty Z1 return sensor 7 12 Faulty Z2 return sensor 7 13 Faulty Z3 return sensor 7 14 Faulty Z4 return sensor 7 15 Faulty Z5 return sensor 7 16 Faulty Z6 return sensor 7 22 Zone 2 overheat 7 23 Zone 3 overheat 7 25 Zone 5 overheat 7 26 Zone 6 overheat 7 50 Hydraulics diagram not defined 7 51 Zone error 7 52 116

table of error codes GB ERROR 9 01 DESCRIPTION BUS communication error Energy Manager 9 02 Separator flow sensor Faulty 9 03 Faulty separator return sensor 9 04 Type 1 HP lock 9 05 HP evaporator sensor error 9 06 HP gas sensor error 9 07 HP HST sensor error 9 08 HP outdoor temp. sensor error 9 09 HP OMT sensor error 9 10 No communication with HYDI 9 11 Faulty HP pressure sensor (AC) 9 12 Faulty HP pressure sensor (DC) 9 13 Faulty HP flow sensor (AC) 9 14 Faulty HP flow sensor (DC) 9 15 Faulty HP condenser sensor 9 16 HP HYDI-ODU communication error 9 17 Faulty HP return sensor 9 18 Type 2 HP lock 9 19 HP awaiting restart 9 20 Separator sensors error (flow+ret) 9 21 Electricity/gas cost ratio error 9 22 HP locked 9 23 Heating circuit pressure error 9 24 Error in communication with HP 9 25 No boiler 9 30 Energy Manager error 9 31 Energy Manager error Restoring operation If the system shuts down, a code will appear on the system interface display signalling the type of shutdown and the reason behind it. To restore normal operation, follow the instructions provided on the display or, if the error persists, contact an authorised Technical Service Centre for assistance. (*) BUS power supply overload A BUS power supply overload error may occur due to the connection of three or more devices within the installed system. Devices which may overload the BUS network include: - Multizone module - Solar pump assembly - Module for instant production of domestic hot water To avoid overloading the BUS power supply, set microswitch 1 on one of the P.C.B.s inside the equipment connected to the system (except the boiler) to OFF, as illustrated in the figure. microswitch 1 2 ON OFF 117

MANUALS