Nimbus Pocket M NET R32 Installation Manual UK

Commissioning 4 Safety

Commissioning 4 Safety thermostat: connect an underfloor safety thermostat to the contact. When the contact is closed, water circulation is interrupted. 5 Photovoltaic integration: input not active (contact open), no integration. Input active (contact closed), the energy surplus is used to increase the DHW set-point by the quantity defined through parameter 1.20.0 PV offset DHW setpoint temperature - Delta T Setpoint DHW photovoltaic. If the DHW calorifier has reached the new set-point, it is possible to use this energy to increase the set-point of the inertial storage tank (if present) through parameter 20.4.4 Buffer electric integration offset or of the heating / cooling function to the comfort set-point. Press the selector to confirm. 1.1.5 Electric heat sources blocking type Press the selector . Turn the selector to choose the desired item. 0 None. The company block function is not specified. 1 Soft Lock-Out. The energy provider can send a signal to switch off the heat pump. 2 Hard Lock-Out. The energy provider shuts off the power supply to the heat pump. 3 Hybrid Lock-Out. The energy provider sends a signal and disconnects the power supply to switch off the heat pump. Press the selector to confirm. 1.1.7 CH Press Detection Device Press the selector . Turn the selector to choose the desired item. 0 Not defined. No pressure device present (Lightbox or hybrid system setting) Press the selector to confirm. 1.1.8 System flow T selection Press the selector . Turn the selector to choose the desired item. 0 HP water flow temp: LWT probe is used as water flow probe by the system 1 System flow T: HC flow probe is used as water flow probe by the system Press the selector to confirm. 1.1.9 Humidity input zone This parameter defines to which zones the value of the humidity read by the Energy Manager has to be set. Press the selector . Turn the selector to choose the desired item. 0 All zones 1 Zone 1 2 Zone 2 3 Zone 3 4 Zone 4 5 Zone 5 6 Zone 6 7 Zones 1 , 2 8 Zones 3 , 4 9 Zones 5 , 6 10 Zones 1,2,3 11 Zones 4,5,6 12 No zone set Press the selector to confirm. 1.2 OUTPUT CONFIGURATION 1.2.0 AUX output 1 Press the selector . Turn the selector to choose the desired item. 0 None. 1 Fault alarm: the contact is closed in case of a system error. 2 Humidity Control: the contact is closed when the AUX1 input is set as a humidistat and the contact is closed. 3 External heat and DHW request: the contact is closed to generate a heat request towards an external source for space heating and DHW production. 4 Cooling request: the contact is closed to generate a cooling request towards an external source. 5 DHW request: the contact is closed to generate a heat request towards an external source for DHW. 38 / EN

Commissioning 6 Heat / Cool mode: the contact is closed when the cooling operating mode is active. The contact is opened when the operating mode is heating or stand-by. 7 CH request: the contact is closed to generate a heat request towards an external source for space heating. Press the selector to confirm. 1.2.1 AUX output 2 Press the selector . Turn the selector to choose the desired item. 0 None. 1 Fault alarm: the contact is closed in case of a system error. 2 Humidity Control: the contact is closed when the AUX1 input is set as a humidistat and the contact is closed. 3 External heat and DHW request: the contact is closed to generate a heat request towards an external source for space heating and DHW production. 4 Cooling request: the contact is closed to generate a cooling request towards an external source. 5 DHW request: the contact is closed to generate a heat request towards an external source for DHW. 6 Heat / Cool mode: the contact is closed when the cooling operating mode is active. The contact is opened when the operating mode is heating or stand-by. 7 CH request: the contact is closed to generate a heat request towards an external source for space heating. Press the selector to confirm. 1.2.2 AUX output 3 Press the selector . Turn the selector to choose the desired item. 0 None. 1 Fault alarm: the contact is closed in case of a system error. 2 Humidity Control: the contact is closed when the AUX1 input is set as a humidistat and the contact is closed. 3 External heat and DHW request: the contact is closed to generate a heat request towards an external source for space heating and DHW production. 4 Cooling request: the contact is closed to generate a cooling request towards an external source. 5 DHW request: the contact is closed to generate a heat request towards an external source for DHW. 6 Heat / Cool mode: the contact is closed when the cooling operating mode is active. The contact is opened when the operating mode is heating or stand-by. 7 CH request: the contact is closed to generate a heat request towards an external source for space heating. Press the selector to confirm. 1.2.3 AUX output 4 Press the selector . Turn the selector to choose the desired item. 0 None. 1 Fault alarm: the contact is closed in case of a system error. 2 Humidity Control: the contact is closed when the AUX1 input is set as a humidistat and the contact is closed. 3 External heat and DHW request: the contact is closed to generate a heat request towards an external source for space heating and DHW production. 4 Cooling request: the contact is closed to generate a cooling request towards an external source. 5 DHW request: the contact is closed to generate a heat request towards an external source for DHW. 6 Heat / Cool mode: the contact is closed when the cooling operating mode is active. The contact is opened when the operating mode is heating or stand-by. 7 CH request: the contact is closed to generate a heat request towards an external source for space heating. Press the selector to confirm. 39 / EN