Commissioning 4 Curing
Commissioning 4 Curing Heating + Functional Heating (screed heating at a variable temperature from 25°C to the temperature defined by Par. 1.12.6 Floor drying Flow Set Point T, according to the period specified as an example in the chart for an 18-day period, then at a fixed temperature of 25°C for a period of 3 days, then for a further 4 days at the temperature defined by Par. 1.12.6 Floor drying Flow Set Point T) 1.17 EM DIAGNOSTICS - 2 INPUT 1.18 EM DIAGNOSTICS - 1 OUTPUT Displays the values of the system’s board outputs. 1.19 SERVICE 1.19.0 SW Version main Temperature °C 60 50 40 30 20 10 0 0 5 10 15 20 25 30 Period (days) Fig. 83 5 Manual (screed heating at the temperature set in Par. 1.12.6 Floor drying Flow Set Point T) Press the selector to confirm. 1.20 SYSTEM INTEGRATION 1.20.0 PV offset DHW setpoint temperature Press the selector . Rotate the selector to set the desired value to increase the DHW set-point during integration from the photovoltaic system. Press the selector to confirm. 1.20.2 Tank solar integration Activates integration of the solar heating system. In this case, the high sensor of the solar heating tank is used as a DHW tank sensor. Press the selector . Turn the selector to choose the desired item. 0 Absent. 1 Present. Press the selector to confirm. 1.12.6 Floor drying Flow Set Point T Defines the set-point temperature of the heating delivery during the screed drying function (see Par. 1.12.5 Floor drying cycle). 1.12.7 Floor drying total Remaining Days Defines the days remaining for the screed drying function. 1.12.9 Exogel kit activation Enables integration of the anti-freeze kit. Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.14 ENERGY MANAGER STATISTICS Shows the duration of the system operation in hours. 1.16 EM DIAGNOSTICS - 1 INPUT Displays the values of the system’s board inputs. 1.20.3 OpenTherm gateway activation Activates the Opentherm gateway. Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.21 ERROR HISTORY 1.21.0 Last 10 errors Displays the last 10 errors. 1.21.1 Reset error list Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 1.22 RESET MENU 1.22.0 Reset factory settings Restores the default settings. Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 52 / EN
Commissioning 1.23 DOMESTIC HOT WATER - 2 1.23.0 Thermal Cleanse target temp Defines the setpoint of thermal cleanse cycle. 1.23.1 Antilegionella target temperature duration Defines the time in which the Thermal cleanse Target temp has to be mantained. 1.23.2 Max Duration Antilegionella Defines the Max time in which the system can perform and complete the Thermal cleanse cycle. 1.24.4 Backup electric heaters nominal power Backup Heating Element Nominal Power Consumption. 1.24.5 Tank electric heaters nominal power Tank electric heaters nominal power consumption. 1.24.6 Backup electric heaters efficiency Backup Heating Element Nominal efficiency. 1.24.7 Tank electric heaters efficiency Tank electric heaters nominal efficiency. 1.24 ENERGY METER 1.24.0 Energy pulse unit Press the selector . Turn the selector to choose the desired item. Define if the S0 input is used or not: 0 None: S0 signal input is not used. 1 kWh: S0 signal input is used. Press the selector to confirm. 1.24.1 Energy pulse value number 1.24.2 Energy pulse value factor The multiplication of Energy pulse value factor and the Energy pulse value number gives the number of pulses representing an energy consumption of 1 kWh. These parameters must be set according to the connected pulse meter. Specifications. Press the selector . Turn the selector to choose the desired item. 0 /1000 1 /100 2 /10 3 1 4 x10 5 x100 6 x1000 Press the selector to confirm. 1.24.3 Energy pulse measuring type Defines if the S0 input signals measures the HP consumption (0) or the sum HP and resistors consumption (1). Press the selector . Turn the selector to choose the desired item. 0 Only HP. 1 HP + Electric Heater. Press the selector to confirm. EN / 53
X