Nimbus M NET R32 Hybrid Installation Manual UK

Commissioning 7.3

Commissioning 7.3 COOLING 7.3.0 FlowT Offset Cooling 7.3.1 Cooling mode activation 7.3.3 Valves Kp Cooling 7.8 ERROR HISTORY 7.8.0 Last 10 errors 7.8.1 Reset error list Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 7.9 RESET MENU 7.9.0 Reset factory settings Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 13 HEAT PUMP TDM 13.1 INPUT CONFIGURATION 13.1.0 TDM Flow Sensor Type Press the selector . Turn the selector to choose the desired item. 0 Not Selected (Self-Recognition). 1 DN 15. 2 DN 20. Press the selector to confirm. 13.2 OUTPUT CONFIGURATION 13.2.1 HP Electric Heater Config Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.5 MANUAL MODE - 1 13.5.1 Compressor frequency setting 13.5.2 Fan 1 rpm setting 13.5.3 Fan 2 rpm setting 13.6 TEST & UTILITIES 13.6.0 Refrigerant Recover Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.6.1 Defrost Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.7 STATISTICS 13.7.0 HP running hours (h/10) 13.7.1 HP on cycles (n/10) 13.7.2 HP defrost hours (h/10) 13.8 HP DIAGNOSTICS - INPUT 1 13.8.0 Outside air temperature 13.8.1 HP water flow temp 13.8.2 HP water return temp 13.8.3 HP Evaporator temp 13.8.4 HP Suction temp 13.8.5 HP Discharge temp 13.8.6 HP condenser outlet temp 13.8.7 TEO 13.4 WATER CIRCULATION 13.4.4 Target deltaT for pump modulation 13.4.5 Max PWM Pump 13.4.6 Min PWM Pump 64 / EN

Commissioning 13.9 HP DIAGNOSTICS - INPUT 2 13.9.0 Heat pump mode Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 Standby. 2 Cooling. 3 Heating cycle. 4 Booster Heating. 5 Booster Cooling. 6 Rating Heating Mode. 7 Rating Cooling Mode. 8 Freeze Protection. 9 Defrost. 10 High temperature protection. 11 Timeguard. 12 System Fail. 13 Hard System Fail. 14 Pump Down. 15 Soft Fail Mode. 16 Rating only fan. 17 Defrost. 18 Cascade Heating. 19 Cascade cooling. Press the selector to confirm. 13.9.1 Last inverter error 13.9.2 Safety thermostat Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 13.9.3 Flowmeter 13.9.4 Flow Switch Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 13.9.5 Inverter shut off protection 13.9.6 Evaporator pressure P 13.9.7 Condenser pressure P 13.10 HP DIAGNOSTICS - OUTPUT 1 13.10.0 Inverter Capacity 13.10.1 HP actual compressor frequency 13.10.2 HP set compressor modulation 13.10.3 Electric Heater 1 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.10.5 Measured rpm fan 1 13.10.6 Measured rpm fan 2 13.10.7 Expansion valve 13.10.8 Expansion valve 2 13.11 HP DIAGNOSTICS - OUTPUT 2 13.11.0 Compressor on/off Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.11.1 Compressor preheating Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.11.2 Current fan 1 status Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 13.11.3 Current fan 2 status Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 65 / EN