Commissioning IMPORTANT: If the room temperature is higher than the desired value, the curve must be shifted lower. If the room temperature is too low, the curve should be shifted upwards. If the temperature of the room corresponds with the desired value, the curve is correct. In the above graph, the curves have been divided into two groups: – Fan-coil systems – Underfloor systems 4.5.4 Paral shift Turn the selector then set the most suitable value and press the selector to confirm. 4.5.6 Max T Turn the selector press the selector then set the most suitable value and to confirm. 4.5.7 Min T Repeat the steps described previously to set the values for zone 2 (where present), by selecting the 5 Zone 2 parameters menu. 4.5.8 Target deltaT for pump modulation 4.7 ZONE REGULATION PARAMETERS 4.7.0 Heating Type Press the selector . Turn the selector to choose the desired item. 0 Floor Heating. 1 Radiators. 2 Floor Heating (main) + Radiators. 3 Radiators (main) + Floor Heating. 4 Convection. 5 Air Heating. Press the selector to confirm. 4.7.1 Room Influence Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 Less. 2 Medium. 3 More. Press the selector to confirm. 4.7.2 Building Isolation Level Press the selector . Turn the selector to choose the desired item. 0 Poor. 1 Medium. 2 Good. Press the selector to confirm. 4.7.3 Building Size Press the selector . Turn the selector to choose the desired item. 0 Small. 1 Medium. 2 Large. Press the selector to confirm. 4.7.4 Climatic Zone 4.7.5 Auto Slope Adaptation Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 4.8 ADVANCED SETTINGS 4.8.3 Heating controller Press the selector . Turn the selector to choose the desired item. 0 None. 1 Room thermostat. 2 Room Sensor. Press the selector to confirm. 4.8.4 Cooling controller Press the selector . Turn the selector to choose the desired item. 0 None. 1 Room thermostat. 2 Room Sensor. Press the selector to confirm. 4.8.7 Humidity Control Threshold 4.8.8 Humidity Control Hysteresis 4.8.9 Humidity control Press the selector . Turn the selector to choose the desired item. 0 None. 1 Stop. Press the selector to confirm. 5 ZONE 2 PARAMETERS 5.0 SETPOINT 5.0.0 T Day 5.0.1 T Night 5.0.2 T set Z2 5.0.3 Zone frost temperature 60 / EN
Commissioning 5.1 AUTOMATIC WINTER MODE 5.1.0 Automatic winter mode activation Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.1.1 Automatic winter mode threshold 5.1.2 Automatic winter mode delay time 5.2 SETUP 5.2.0 Zone temperature range Press the selector . Turn the selector to choose the desired item. 0 Low Temp. 1 High Temp. Press the selector to confirm. 5.2.1 Thermoregulation Press the selector . Turn the selector to choose the desired item. 0 Fix Flow T. 1 Basic Thermoreg. 2 Room T Only. 3 Outdoor T Only. 4 Room+Outdoor T. Press the selector to confirm. 5.2.2 Slope 5.2.3 Paral shift 5.2.4 Room Influence Proportional 5.2.5 Max T 5.2.6 Min T 5.2.7 Thermoregulation logic Press the selector . Turn the selector to choose the desired item. 0 Classic. 1 Smart. Press the selector to confirm. 5.2.8 Quick night setback Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.2.9 Heat request mode Press the selector . Turn the selector to choose the desired item. 0 Standard. 1 RT Time Programs Exclusion. 2 Forcing Heat Demand. Press the selector to confirm. 5.3 DIAGNOSTICS 5.3.0 Room T 5.3.1 Room T setpoint 5.3.2 Flow temperature 5.3.3 Return temperature 5.3.4 Heat Request Z2 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.3.5 Pump status Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.3.7 Relative humidity 5.3.8 Zone flow temperature setpoint 5.4 ZONE MODULE SETTINGS 5.4.0 Zone pump modulation Press the selector . Turn the selector to choose the desired item. 0 Fixed. 1 Modulating on DeltaT. 2 Modulating on pressure. Press the selector to confirm. 5.4.1 Target deltaT for pump modulation 5.4.2 Pump fixed speed 61 / EN
Commissioning IMPORTANT: If the room temperature is higher than the desired value, the curve must be shifted lower. If the room temperature is too low, the curve should be shifted upwards. If the temperature of the room corresponds with the desired value, the curve is correct. In the above graph, the curves have been divided into two groups: – Fan-coil systems – Underfloor systems 4.5.4 Paral shift Turn the selector then set the most suitable value and press the selector to confirm. 4.5.6 Max T Turn the selector press the selector then set the most suitable value and to confirm. 4.5.7 Min T Repeat the steps described previously to set the values for zone 2 (where present), by selecting the 5 Zone 2 parameters menu. 4.5.8 Target deltaT for pump modulation 4.7 ZONE REGULATION PARAMETERS 4.7.0 Heating Type Press the selector . Turn the selector to choose the desired item. 0 Floor Heating. 1 Radiators. 2 Floor Heating (main) + Radiators. 3 Radiators (main) + Floor Heating. 4 Convection. 5 Air Heating. Press the selector to confirm. 4.7.1 Room Influence Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 Less. 2 Medium. 3 More. Press the selector to confirm. 4.7.2 Building Isolation Level Press the selector . Turn the selector to choose the desired item. 0 Poor. 1 Medium. 2 Good. Press the selector to confirm. 4.7.3 Building Size Press the selector . Turn the selector to choose the desired item. 0 Small. 1 Medium. 2 Large. Press the selector to confirm. 4.7.4 Climatic Zone 4.7.5 Auto Slope Adaptation Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 4.8 ADVANCED SETTINGS 4.8.3 Heating controller Press the selector . Turn the selector to choose the desired item. 0 None. 1 Room thermostat. 2 Room Sensor. Press the selector to confirm. 4.8.4 Cooling controller Press the selector . Turn the selector to choose the desired item. 0 None. 1 Room thermostat. 2 Room Sensor. Press the selector to confirm. 4.8.7 Humidity Control Threshold 4.8.8 Humidity Control Hysteresis 4.8.9 Humidity control Press the selector . Turn the selector to choose the desired item. 0 None. 1 Stop. Press the selector to confirm. 5 ZONE 2 PARAMETERS 5.0 SETPOINT 5.0.0 T Day 5.0.1 T Night 5.0.2 T set Z2 5.0.3 Zone frost temperature 60 / EN
Commissioning 5.1 AUTOMATIC WINTER MODE 5.1.0 Automatic winter mode activation Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.1.1 Automatic winter mode threshold 5.1.2 Automatic winter mode delay time 5.2 SETUP 5.2.0 Zone temperature range Press the selector . Turn the selector to choose the desired item. 0 Low Temp. 1 High Temp. Press the selector to confirm. 5.2.1 Thermoregulation Press the selector . Turn the selector to choose the desired item. 0 Fix Flow T. 1 Basic Thermoreg. 2 Room T Only. 3 Outdoor T Only. 4 Room+Outdoor T. Press the selector to confirm. 5.2.2 Slope 5.2.3 Paral shift 5.2.4 Room Influence Proportional 5.2.5 Max T 5.2.6 Min T 5.2.7 Thermoregulation logic Press the selector . Turn the selector to choose the desired item. 0 Classic. 1 Smart. Press the selector to confirm. 5.2.8 Quick night setback Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.2.9 Heat request mode Press the selector . Turn the selector to choose the desired item. 0 Standard. 1 RT Time Programs Exclusion. 2 Forcing Heat Demand. Press the selector to confirm. 5.3 DIAGNOSTICS 5.3.0 Room T 5.3.1 Room T setpoint 5.3.2 Flow temperature 5.3.3 Return temperature 5.3.4 Heat Request Z2 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.3.5 Pump status Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 5.3.7 Relative humidity 5.3.8 Zone flow temperature setpoint 5.4 ZONE MODULE SETTINGS 5.4.0 Zone pump modulation Press the selector . Turn the selector to choose the desired item. 0 Fixed. 1 Modulating on DeltaT. 2 Modulating on pressure. Press the selector to confirm. 5.4.1 Target deltaT for pump modulation 5.4.2 Pump fixed speed 61 / EN
X