Commissioning 1.21 ERROR HISTORY 1.21.0 Last 10 errors Displays the last 10 errors. 1.21.1 Reset error list Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 1.22 RESET MENU 1.22.0 Reset factory settings Restores the default settings. Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 1.23 DOMESTIC HOT WATER - 2 1.23.0 Thermal Cleanse target temp Defines the setpoint of thermal cleanse cycle. 1.24.2 Energy pulse value factor The multiplication of Energy pulse value factor and the Energy pulse measuring type gives the number of pulses representing an energy consumption of 1 kWh. These parameters must be set according to the connected pulse meter. Specifications. Press the selector . Turn the selector to choose the desired item. 0 /1000 1 /100 2 /10 3 1 4 x10 5 x100 6 x1000 Press the selector to confirm. 1.24.3 Energy pulse measuring type Defines if the S0 input signals measures the HP consumption (0) or the sum HP and resistors consumption (1). Press the selector . Turn the selector to choose the desired item. 0 Only HP. 1 HP + Electric Heater. Press the selector to confirm. 1.23.1 Antilegionella target temperature duration Defines the time in which the Thermal cleanse Target temp has to be mantained. 1.23.2 Max Duration Antilegionella Defines the Max time in which the system can perform and complete the Thermal cleanse cycle. 1.24 ENERGY METER 1.24.0 Energy pulse unit Press the selector . Turn the selector to choose the desired item. Define if the S0 input is used or not: 0 None: S0 signal input is not used. 1 kWh: S0 signal input is used. 2 m3. Press the selector to confirm. 1.24.1 Energy pulse value number 56 / EN
Commissioning 6.8 Temperature adjustment Simultaneously press the “Esc” and “Menu” buttons until “Insert Code” appears on the display. Turn the selector to enter the technical code (234) then press the selector to confirm; the display will show TECHNICAL AREA. Turn the selector to choose the desired item. – COMPLETE MENU Press the selector . Turn the selector to choose the desired item. 4 ZONE 1 PARAMETERS 4.0 SETPOINT 4.0.0 T Day 4.0.1 T Night 4.0.2 T set Z1 4.0.3 Zone frost temperature 4.1 AUTOMATIC WINTER MODE 4.1.0 Automatic winter mode activation [ON, OFF] Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 4.1.1 Automatic winter mode threshold Turn the selector and set the auto summer/winter switching delay. 4.2.2 Slope Press the selector . Turn the selector and set the curve in accordance with the type of heating system. Press the selector to confirm. Low-temperature system (underfloor panels) curve between 0.2 and 0.8. High-temperature system (radiators) curve between 1.0 and 3.5. The checking process for the suitability of the curve requires a long period of time during which several adjustments may be necessary. When the outdoor temperature falls (winter) three conditions may arise: – The temperature of the room may fall, indicating that a steeper curve should be set. – The temperature of the room may rise, indicating that a gentler curve should be set. – The temperature of the room remains constant, indicating that the set curve is exactly right. Once you have found the curve which maintains the room temperature at a constant level, check the actual temperature value. °C 100 1 90 80 70 60 50 40 30 3.5 3.0 2.5 2.0 1.5 1.2 1.0 0.8 0.6 0.4 0.2 5 4 4.1.2 Automatic winter mode delay time Turn the selector and set the auto summer/winter switching delay. 4.2 SETUP 4.2.0 Zone temperature range Press the selector . Turn the selector to choose the desired item. 0 Low Temp. 1 High Temp. Press the selector to confirm. 4.2.1 Thermoregulation Press the selector . Turn the selector to choose the desired item. 0 Fix Flow T. 1 Basic Thermoreg. 2 Room T Only. 3 Outdoor T Only. 4 Room+Outdoor T. Press the selector to confirm. 25 20 15 10 5 0 -5 -10 -15 -20°C 2 3 °C 1 Delivery temperature to the system 2 Delivery value room temperature 3 Outside air temperature 4 Low temperature 5 High temperature Fig. 68 57 / EN
Commissioning 1.21 ERROR HISTORY 1.21.0 Last 10 errors Displays the last 10 errors. 1.21.1 Reset error list Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 1.22 RESET MENU 1.22.0 Reset factory settings Restores the default settings. Press the selector . Turn the selector to choose the desired item. 0 Do you really want to perform the reset ? If you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown.. Press the selector to confirm. 1.23 DOMESTIC HOT WATER - 2 1.23.0 Thermal Cleanse target temp Defines the setpoint of thermal cleanse cycle. 1.24.2 Energy pulse value factor The multiplication of Energy pulse value factor and the Energy pulse measuring type gives the number of pulses representing an energy consumption of 1 kWh. These parameters must be set according to the connected pulse meter. Specifications. Press the selector . Turn the selector to choose the desired item. 0 /1000 1 /100 2 /10 3 1 4 x10 5 x100 6 x1000 Press the selector to confirm. 1.24.3 Energy pulse measuring type Defines if the S0 input signals measures the HP consumption (0) or the sum HP and resistors consumption (1). Press the selector . Turn the selector to choose the desired item. 0 Only HP. 1 HP + Electric Heater. Press the selector to confirm. 1.23.1 Antilegionella target temperature duration Defines the time in which the Thermal cleanse Target temp has to be mantained. 1.23.2 Max Duration Antilegionella Defines the Max time in which the system can perform and complete the Thermal cleanse cycle. 1.24 ENERGY METER 1.24.0 Energy pulse unit Press the selector . Turn the selector to choose the desired item. Define if the S0 input is used or not: 0 None: S0 signal input is not used. 1 kWh: S0 signal input is used. 2 m3. Press the selector to confirm. 1.24.1 Energy pulse value number 56 / EN
Commissioning 6.8 Temperature adjustment Simultaneously press the “Esc” and “Menu” buttons until “Insert Code” appears on the display. Turn the selector to enter the technical code (234) then press the selector to confirm; the display will show TECHNICAL AREA. Turn the selector to choose the desired item. – COMPLETE MENU Press the selector . Turn the selector to choose the desired item. 4 ZONE 1 PARAMETERS 4.0 SETPOINT 4.0.0 T Day 4.0.1 T Night 4.0.2 T set Z1 4.0.3 Zone frost temperature 4.1 AUTOMATIC WINTER MODE 4.1.0 Automatic winter mode activation [ON, OFF] Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 4.1.1 Automatic winter mode threshold Turn the selector and set the auto summer/winter switching delay. 4.2.2 Slope Press the selector . Turn the selector and set the curve in accordance with the type of heating system. Press the selector to confirm. Low-temperature system (underfloor panels) curve between 0.2 and 0.8. High-temperature system (radiators) curve between 1.0 and 3.5. The checking process for the suitability of the curve requires a long period of time during which several adjustments may be necessary. When the outdoor temperature falls (winter) three conditions may arise: – The temperature of the room may fall, indicating that a steeper curve should be set. – The temperature of the room may rise, indicating that a gentler curve should be set. – The temperature of the room remains constant, indicating that the set curve is exactly right. Once you have found the curve which maintains the room temperature at a constant level, check the actual temperature value. °C 100 1 90 80 70 60 50 40 30 3.5 3.0 2.5 2.0 1.5 1.2 1.0 0.8 0.6 0.4 0.2 5 4 4.1.2 Automatic winter mode delay time Turn the selector and set the auto summer/winter switching delay. 4.2 SETUP 4.2.0 Zone temperature range Press the selector . Turn the selector to choose the desired item. 0 Low Temp. 1 High Temp. Press the selector to confirm. 4.2.1 Thermoregulation Press the selector . Turn the selector to choose the desired item. 0 Fix Flow T. 1 Basic Thermoreg. 2 Room T Only. 3 Outdoor T Only. 4 Room+Outdoor T. Press the selector to confirm. 25 20 15 10 5 0 -5 -10 -15 -20°C 2 3 °C 1 Delivery temperature to the system 2 Delivery value room temperature 3 Outside air temperature 4 Low temperature 5 High temperature Fig. 68 57 / EN
X