Nimbus M NET R32 Hybrid Installation Manual UK

Commissioning 1.16 EM

Commissioning 1.16 EM DIAGNOSTICS - 1 INPUT Displays the values of the system’s board inputs. 1.16.0 Energy Manager status Press the selector . Turn the selector to choose the desired item. 0 Standby. 1 Antifreeze cycle. 2 Heating cycle. 3 Heating temperature reached. 4 DHW cycle. 5 Thermal cleanse function. 6 Air purge function. 7 Chimney function. 8 Floor drying cycle. 9 No heat generation. 10 Manual mode. 11 Fault. 12 Initialization. 13 OFF. 14 Cooling. 15 DHW antifreeze. 16 Photovoltaic integration. 17 Dehumidification. 18 Pump Down. 19 Defrost. 20 Buffer Heating+DHW Serving. 21 Buffer Cooling+DHW Serving. 22 Buffer Heating Serving. 23 Buffer Cooling Serving. 24 Automatic calibration. Press the selector to confirm. 1.16.1 Hydraulic scheme diagnostic Press the selector . Turn the selector to choose the desired item. 0 None. 1 Hybrid combi. 2 Hybrid system. 3 Hybrid system with thermostat. 4 Pacman plus. 5 Pacman flex. 6 Pacman flex with thermostat. 7 Pacman light plus. 8 Pacman light flex. 9 Pacman light flex with thermostat. Press the selector to confirm. 1.17 EM DIAGNOSTICS - 2 INPUT 1.17.0 Room Thermostat 1 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.17.1 Room Thermostat 2 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.17.2 AUX input 1 Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 1.17.3 AUX input 2 Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 1.17.4 HV input 1 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.17.5 HV input 2 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.16.2 CH flow set T 1.16.3 CH flow temperature 1.16.5 DHW storage temperature 54 / EN

Commissioning 1.18 EM DIAGNOSTICS - 1 OUTPUT Displays the values of the system’s board outputs. 1.18.0 CH Circulator status Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.18.2 HC Pump 2 Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.18.3 Diverter Valve (CH/DHW) Press the selector . Turn the selector to choose the desired item. 0 DHW cycle. 1 Heating cycle. Press the selector to confirm. 1.18.4 Diverter Valve 2 (CH/Cooling) Press the selector . Turn the selector to choose the desired item. 0 Heating cycle. 1 Cooling. Press the selector to confirm. 1.18.8 AUX output 1 Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 1.18.9 AUX output 2 Press the selector . Turn the selector to choose the desired item. 0 Open. 1 Close. Press the selector to confirm. 1.19 SERVICE 1.19.0 SW Version main 1.20 SYSTEM INTEGRATION 1.20.0 PV offset DHW setpoint temperature Press the selector . Rotate the selector to set the desired value to increase the DHW set-point during integration from the photovoltaic system. Press the selector to confirm. 1.20.2 Tank solar integration Activates integration of the solar heating system. In this case, the high sensor of the solar heating tank is used as a DHW tank sensor. Press the selector . Turn the selector to choose the desired item. 0 Absent. 1 Present. Press the selector to confirm. 1.20.3 OpenTherm gateway activation Activates the Opentherm gateway. Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 55 / EN