Commissioning 1.9 DHW
Commissioning 1.9 DHW CYCLE 1.9.0 DHW comfort setpoint temp. Defines the comfort DHW set-point temperature. 1.9.1 DHW reduced setpoint temp. Defines the reduced DHW set-point temperature. 1.9.2 Comfort Function Press the selector . Turn the selector to choose the desired item. Configures the domestic hot water production mode as follows: 0 Disabled. 1 Timer based (starts the comfort function for time periods that can be adjusted according to the DHW time schedule). 2 Always active. Press the selector to confirm. 1.9.4 Tank charge mode Press the selector . Turn the selector to choose the desired item. 0 Standard: automatic operating mode. 1 Only HP: excludes the operation of the boiler. 2 Fast: excludes the operation of the heat pump, except when the boiler is not available. Press the selector to confirm. 1.9.5 Max HP charging time Defines the filling time, carried out only with the heat pump, after which the auxiliary integration sources are switched on when there is no sensor in the calorifier but only the thermostat (Par. 1.0.2 Tank management = 2). 1.9.6 Thermal cleanse function Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. NOTE: when the function is enabled, the DHW calorifier is heated and maintained at 60°C for one hour starting from the function start time (see Par. 1.9.7 Thermal Cleanse start time [hh:mm]), only if there is a calorifier sensor (Par. 1.0.2 Tank management = 1). The operation is repeated after a time period defined by Par. 1.9.8 Thermal Cleanse Cycle frequency. Press the selector to confirm. 1.9.7 Thermal Cleanse start time [hh:mm] Defines the start time of the DHW tank sanitisation function. 1.9.8 Thermal Cleanse Cycle frequency Sets the period of time after which the DHW tank sanitisation function is repeated. 1.10 MANUAL MODE - 1 1.10.0 Manual mode activation Manual activation of the system components (circulation pumps, diverter valves, heating elements, etc.). Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.10.1 HP circulator control Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 Low speed. 2 High speed. Press the selector to confirm. 50 / EN
Commissioning 1.10.2 Diverter valve control Press the selector . Turn the selector to choose the desired item. 0 DHW cycle. 1 Heating cycle. Press the selector to confirm. 1.10.3 Diverter valve COOLING Press the selector . Turn the selector to choose the desired item. 0 Heating cycle. 1 Cooling. Press the selector to confirm. 1.10.4 Auxiliary circulator Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.10.8 All output AUX contact Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.10.9 Anode output Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.11 MANUAL MODE - 2 1.11.0 Manual mode activation Manual activation of the system components (circulation pumps, diverter valves, heating elements, etc.). Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.11.1 Force Hp Heat Activates the heat pump in heating mode. Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.11.2 Force Hp Cool Activates the heat pump in cooling mode. Press the selector . Turn the selector to choose the desired item. 0 OFF. 1 ON. Press the selector to confirm. 1.11.3 Force WHB Turn the selector to navigate to ON, then press the selector to confirm. The boiler is forced to the maximum heating power. Turn the selector to select operation at maximum DHW power or at minimum power. 51 / EN
X