AristonThermoUK
Views
1 year ago
Flag

Nimbus Compact M NET R32 Installation Manual UK

  • Text
  • Heat pump
  • Selector
  • Heating
  • Outdoor
  • Electrical
  • Cooling
  • Desired
  • Valve
  • Active
  • Sensor
  • Connections
  • Nimbus
  • Compact
  • Installation
  • Manual
  • Wwwaristoncom

Electrical connections

Electrical connections – Pass the BUS cable (5) through the hole (6) on the electrical panel. – Open the flap (9) of the housing and insert the interface (10). 10 5 6 9 Fig. 73 – Open the internal panel (7) to access the housing (8) of the interface. 3 Fig. 75 – Close the flap (9). – Once the interface has been installed on board, make sure that the bus communication cable passes through the hole (6) in the electrical panel, continues along the panel (7) and is then connected to the terminal board of the interface (11). – Close the internal panel (7) and the front panel (2). 7 6 11 4 Fig. 74 Fig. 76 42 / EN

Electrical connections Signal sending, receiving, and decoding is carried out using BUS protocol, which ensures the interaction between the system and the interface. Connect the cables to the terminal board located in the system’s indoor unit panel. NOTE: Use a shielded cable or a twisted-pair cable to connect the system interface and the indoor unit so as to avoid interference problems. 5.5 Installing the Light Gateway Note: when installing cascade systems, to install the Light Gateway interface refer to the relevant dedicated manual. i The proper operation of the Light Gateway device depends on the power of the Wi-Fi signal in the point of installation. Make sure that the place of installation is covered by a sufficiently powerful Wi-Fi signal. In case of poor coverage of the Wi-Fi network, install the Light Gateway as close as possible to a Wi-Fi source. – Remove the screw (1) and open the front panel (2). B T 2 B T Blue Orange Fig. 77 1 Fig. 78 – Open the internal panel (3) to access the housing (4). 3 4 Fig. 79 EN / 43

MANUALS

AristonThermoUK
Views
1 year ago
Flag

Nimbus Compact M NET R32 Installation Manual UK

  • Text
  • Heat pump
  • Selector
  • Heating
  • Outdoor
  • Electrical
  • Cooling
  • Desired
  • Valve
  • Active
  • Sensor
  • Connections
  • Nimbus
  • Compact
  • Installation
  • Manual
  • Wwwaristoncom

Electrical connections

Electrical connections – Pass the BUS cable (5) through the hole (6) on the electrical panel. – Open the flap (9) of the housing and insert the interface (10). 10 5 6 9 Fig. 73 – Open the internal panel (7) to access the housing (8) of the interface. 3 Fig. 75 – Close the flap (9). – Once the interface has been installed on board, make sure that the bus communication cable passes through the hole (6) in the electrical panel, continues along the panel (7) and is then connected to the terminal board of the interface (11). – Close the internal panel (7) and the front panel (2). 7 6 11 4 Fig. 74 Fig. 76 42 / EN

Electrical connections Signal sending, receiving, and decoding is carried out using BUS protocol, which ensures the interaction between the system and the interface. Connect the cables to the terminal board located in the system’s indoor unit panel. NOTE: Use a shielded cable or a twisted-pair cable to connect the system interface and the indoor unit so as to avoid interference problems. 5.5 Installing the Light Gateway Note: when installing cascade systems, to install the Light Gateway interface refer to the relevant dedicated manual. i The proper operation of the Light Gateway device depends on the power of the Wi-Fi signal in the point of installation. Make sure that the place of installation is covered by a sufficiently powerful Wi-Fi signal. In case of poor coverage of the Wi-Fi network, install the Light Gateway as close as possible to a Wi-Fi source. – Remove the screw (1) and open the front panel (2). B T 2 B T Blue Orange Fig. 77 1 Fig. 78 – Open the internal panel (3) to access the housing (4). 3 4 Fig. 79 EN / 43

Search