Genus ONE+ WiFi Installation Manual

Ariston Genus ONE+ WiFi Installation and Servicing Manual

TECHNICAL AREA menu

TECHNICAL AREA menu sub-menu parameter description value default setings menu sub-menu parameter description value default setings 6. 2. 3 Offset Auto Function active from - 14 to + 14 (°C) (high temperature) from - 7 to + 7 (°C) (low temperature) To adapt the heating curve to the system requirements, shift the curve in parallel so that the calculated flow temperature is modified, in addition to the room temperature. By accessing the parameter and pressing the button b, it is possible to shift the curve in a parallel direction. The shifting value can be read on the display: from -14 to +14 for high-temperature devices, or from -7 to 7 for low-temperature devices. Each step corresponds to a 1°C increase/ decrease In the flow temperature with respect to the set-point value. 6. 2. 4 Room Influence from 0 to 20 20 Proportional Auto Function active If setted = 0 the room temperature doesn’t influence the calculation of the set-point. If setted = 20, the room temperature has the maximun influence to calculate the set-point - only active when the BUS device is connected 6. 2. 5 Maximum CH Temperature Zone 3 6. 2. 6 Minimum CH Temperature Zone 3 from 35 to 82 °C (Param. 620 = 1) from 20 to 45 °C (Param. 620 = 0) from 35 to 82 °C (Param. 620 = 1) from 20 to 45 °C (Param. 620 = 0) 6. 3 Z3 DIAGNOSTICS 6. 3. 0 < Not Available> 6. 3. 4 Heat request Zone 2 0 = OFF 1 = ON 8 SERVICE PARAMETERS 8. 0 BOILER STATISTICS - 1 8. 0. 0 Diverter valve cycles No. (nx10) 8. 0. 1 Time of circulator on (nx10) 8. 0. 2 Boiler circulator cycles No. (nx10) 8. 0. 3 Boiler Life Time (hx10) 8. 0. 4 Time of fan ON (hx10) 8. 0. 5 Fan cycles No. (nx10) 8. 0. 6 CH flame detection (nx10) 8. 0. 7 DHW flame detection (nx10) 8. 1 BOILER STATISTICS - 2 8. 1. 0 Hours Burner On CH (hx10)) 8. 1. 1 Hours Burner On DHW (hx10) 8. 1. 2 Number of Flame Faults (nx10) 8. 1. 3 Numbeer of ignition Cycles (nx10) 8. 1. 4 Heat request Duration 8. 2 BOILER 8. 2. 1 Fan Status 0 = OFF 1 = ON 8. 2. 2 Fan Speed - x100 RPM 8. 2. 3 Pump speed - NOT ACTIVE 0 0 82 45 35 20 8. 2. 4 Diverter valve position 0 = D.H.W. 1 = Central Heating 8. 2. 5 D.H.W. Flow Rate (l/min) 8. 2. 7 Pump Modulation % 8. 2. 8 Gas Power (kW) 8. 3 BOILER TEMPERTURE 8. 3. 0 CH Flow set Temperature(°C) 8. 3. 1 CH Flow Temperature(°C) 8. 3. 2 CH Return Temperature(°C) 8. 3. 3 DHW Temperature (°C) 8. 3. 4 < Not Available> 8. 3. 5 Outdoor temperature (°C) Only with external sensor connected 8. 4 STORAGE 8. 4. 2 D.H.W. Inlet Temperature (°C) Display only with Solar Kit or external storage Kit 8. 5 SERVICE 8. 5. 0 Months to next maintenance from 0 to 60 (month) If setted the boiler will display that is time to call the installer for maintenance ALERT 8. 5. 1 Maintenance on Day At 8. 5. 2 Maintenance Warning Reset Semnalare 3P9 intretinere programata - chemati asistenta tehnica 0 = OFF 1 =ON Reset? OK= Yes Esc = No to erase the advice for maintenance 8. 5. 4 SW version Interface 8. 5. 5 SW version Main 8. 6 ERROR HISTORY 8. 6. 0 Last 10 Errors from Fault 0 to Fault 9 This parameter makes it possible to see the last 10 errors shown by the boiler as well as the relevant day, month and year. Turning the encoder allows for viewing the sequence of errors that occurred, from 0 to 9. 8.6.0 Last 10 errors Fault 3 No flame detected 501 12:18 24/01/2012 8. 6. 1 Reset Error List Reset? Ok=Yes Esc=No 8. 7 FREE PARAMETERS 8. 7. 4 Boiler Flowswitch 0 = Open 1 = Closed 8. 7. 6 Safety flame sensor 8. 7. 8 Boiler power level 8. 7. 9 Ionization current 24 / 48 420011270900 - Rev. 04 - 072024

TECHNICAL AREA menu sub-menu parameter description value default setings menu sub-menu parameter description value default setings 8. 8 DIAGNOSTICS 8. 8. 0 < Not Available> 8. 8. 1 < Not Available> 8. 8. 2 < Not Available> 8. 8. 3 < Not Available> 8. 8. 4 Pump speed 8. 8. 5 Pump flow rate 8. 8. 6 Instant Pump Power Consumption 8. 8. 7 Pump Mains AC Voltage 8. 10. DIAGNOSTICS 2 8. 10. 0 Calibration counter 8. 10. 1 Ionization base value 8. 10. 2 Ignition time 8. 10. 3 Minimum startup ionization value 19 WI - FI (only for ALTEAS ONE+ NET) 19. 0 WI-FI CONFIGURATION 19. 0. 0 Wi-Fi activation 0 = OFF 1 = ON 19. 0. 1 Network configuration 0 = OFF 1 = ON 19. 0. 2 19. 0. 3 Internet time 0 = OFF 1 = ON 19. 0. 5 On line outdoor temperature corr. 19. 1 CONNECTIVITY INFO 19. 1. 0 Connectivity status OFF Initialization Idle Acess Point initializing Acess Point mode on Station Mode - Connecting Station Mode - Connected Station Mode - Provisioning Station Mode - Server Connected Wifi error 19. 1. 1 Signal level 19. 1. 2 Active Status Not provisioned Provisioned - Not active Active 19. 1. 3 Serial Number 19. 1. 4 SW Upgrade Status Initialization Waiting for Update Updating Micro 1 Updating Micro 2 19. 1. 5 On line outdoor temperature 19. 1. 6 On line weather data 19. 2 RESET MENU 19. 2. 0 Factory Reset (soft reset) Do you really want to perform the reset? if you press OK button, the reset command will be executed otherwise, by way of ESC, the previous page is shown. Installation and servicing instructions / 49