Genus ONE+ WiFi Installation Manual

Ariston Genus ONE+ WiFi Installation and Servicing Manual

TECHNICAL AREA menu

TECHNICAL AREA menu sub-menu parameter description value default setings menu sub-menu parameter description value default setings 2. 8 RESET MENU’ 2 2. 8. 0 Reset Factory Settings Reset OK = yes ESC = no To reset all default parameter settings, press the OK button 2. 11 BOILER SETTINGS 2. 11. 0 Gas start offset adj from 0 to 30 9 2. 11. 1 Gas Control Offset from 0 to 190 88 2. 11. 2 Flue Duct Adj from 0 to 20 (%) 0 2. 11. 3 Enable standby calibration 2. 11. 4 Enable calibration CH switch 2. 11. 5 Enable DHW calibrataion threshold temperature 0 = OFF 1 = ON 0 = OFF 1 = ON 0 = OFF 1 = ON 2. 11. 6 DHW ignition threshold from 0 to 5 (°C) 0 2. 12 ADVANCED SETTINGS 2 2. 12. 1 Max DHW adjustable from 0 to 100 (%) 100 4 ZONE 1 PARAMETERS 4. 0 SETPOINT 4. 0. 2 T set Zone 1 from 35 to 82 (°C) (high temperature) from 20 to 45 (°C) (low temperature) To set only with Fixed Flow Temperaure (see 421) 4. 2 ZONE 1 SETTINGS 4. 2. 0 Zone 1 Temperature range 4. 2. 1 Thermoregulation To enabled thermoregulation press Auto button. On the dispaly will appear the symbol AUTO 0 = from 20 to 45°C (low temperature) 1 = from 35 to 82°C (high temperature) 0 = Fixed Flow Temperature 1 = Basic Thermoregulation 2 = Room Temp only 3 = Outdoor Temp. only 4 = Room + outdoor Temp. 1 1 0 1 70 25 1 4. 2. 2 Slope from 1.0 to 3.5 (high temperature) from 0.2 to 1.0 (low temperature) Flow Temperature 90 °C 80 70 60 50 40 30 20 23 °C Ambiente temperature setting value 10 23 0 25 21 21 19 19 20 °C 15 10 3.5 3.0 5 2.5 1.0 2.0 0.8 External temperature 1.8 1.5 1.3 1.0 0.8 0.6 0.4 0 -5 -10 -15 -20 -25 °C 0.6 0.4 0.2 Low temperature High temperature 1.3 0.6 When an outdoor sensor is used, the boiler calculates the most suitable delivery temperature, taking into account the outside temperature and type of system. The type of curve should be selected in correspondence with the projected temperature of the system and the nature of the dispersions present in the structure. For high-temperature systems, one of the curves depicted below may be chosen. 4. 2. 3 Offset Auto Function active from - 14 to + 14 (°C) (high temperature) from - 7 to + 7 (°C) (low temperature) To adapt the heating curve to the system requirements, shift the curve in parallel so that the calculated flow temperature is modified, in addition to the room temperature. By accessing the parameter and pressing the button b, it is possible to shift the curve in a parallel direction. The shifting value can be read on the display: from -14 to +14 for high-temperature devices, or from -7 to 7 for low-temperature devices. Each step corresponds to a 1°C increase/ decrease In the flow temperature with respect to the set-point value. 4. 2. 4 Room Influence from 0 to 20 20 Proportional Auto Function active If setted = 0 the room temperature doesn’t influence the calculation of the set-point. If setted = 20, the room temperature has the maximun influence to calculate the set-point - only active when the BUS device is connected 4. 2. 5 Maximum CH Temperature Zone 1 4. 2. 6 Minimum CH Temperature Zone 1 4. 3 Z1 DIAGNOSTICS 4. 3. 4 Heat request Zone 1 0 = OFF 1 = ON from 35 to 82 °C (Param. 420 = 1) from 20 to 45 °C (Param. 420 = 0) from 35 to 82 °C (Param. 420 = 1) from 20 to 45 °C (Param. 420 = 0) 0 0 82 45 35 20 / 46 420011270900 - Rev. 04 - 072024

TECHNICAL AREA menu sub-menu parameter description value default setings menu sub-menu parameter description value default setings 5 ZONE 2 PARAMETERS 5. 0 SETPOINT 5. 0. 2 T set Zone 2 from 35 to 82 (°C) (high temperature) from 20 to 45 (°C) (low temperature) To set only with Fixed Flow Temperaure of Thermoregulation (see 521) 5. 2 ZONE 2 SETTING 5. 2. 0 Zone 2 Temperature range 5. 2. 1 Thermoregulation To enabled thermoregulation press Auto button. On the dispaly will appear the symbol AUTO 0 = from 20 to 45°C (low temperature) 1 = from 35 to 82°C (high temperature) 0 = Fixed Flow Temperature 1 = Basic Thermoregulation 2 = Room Temp only 3 = Outdoor Temp. only 4 = Room + outdoor Temp. 5. 2. 2 Slope from 1.0 to 3.5 1.3 (high temperature) from 0.2 to 1.0 0.6 (low temperature) See parameter 422 Only enabled when an outdoor sensor is installed When an outdoor sensor is used, the boiler calculates the most suitable delivery temperature, taking into account the outside temperature and type of system. The type of curve should be selected in correspondence with the projected temperature of the system and the nature of the dispersions present in the structure. For high-temperature systems, one of the curves depicted below may be chosen. 5. 2. 3 Offset Auto Function active from - 14 to + 14 (°C) (high temperature) from - 7 to + 7 (°C) (low temperature) 1 70 25 To adapt the heating curve to the system requirements, shift the curve in parallel so that the calculated flow temperature is modified, in addition to the room temperature. By accessing the parameter and pressing the button b, it is possible to shift the curve in a parallel direction. The shifting value can be read on the display: from -14 to +14 for high-temperature devices, or from -7 to 7 for low-temperature devices. Each step corresponds to a 1°C increase/ decrease In the flow temperature with respect to the set-point value. 1 0 0 5. 2. 4 Room Influence from 0 to 20 20 Proportional Auto Function active If setted = 0 the room temperature doesn’t influence the calculation of the set-point. If setted = 20, the room temperature has the maximun influence to calculate the set-point - only active when the BUS device is connected 5. 2. 5 Maximum CH Temperature Zone 2 5. 2. 6 Minimum CH Temperature Zone 2 5. 3 Z2 DIAGNOSTICS from 35 to 82 °C (Param. 520 = 1) from 20 to 45 °C (Param. 520 = 0) from 35 to 82 °C (Param. 520 = 1) from 20 to 45 °C (Param. 520 = 0) 5. 3. 4 Heat request Zone 2 0 = OFF 1 = ON 6 ZONE 3 PARAMETER 6. 0 SETPOINT 6. 0. 2 T set Zone 3 from 35 to 82 (°C) 70 To set only with Fixed Flow Temperaure of Thermoregulation (see 521) 6. 2 ZONE 3 SETTING 6. 2. 0 Zone 3 Temperature range 6. 2. 1 Thermoregulation To enabled thermoregulation press Auto button. On the dispaly will appear the symbol AUTO 0 = from 20 to 45°C (low temperature) 1 = from 35 to 82°C (high temperature) 0 = Fixed Flow Temperature 1 = Basic Thermoregulation 2 = Room Temp only 3 = Outdoor Temp. only 4 = Room + outdoor Temp. 6. 2. 2 Slope from 1.0 to 3.5 1.3 (high temperature) from 0.2 to 1.0 0.6 (low temperature) See parameter 422 Only enabled when an outdoor sensor is installed When an outdoor sensor is used, the boiler calculates the most suitable delivery temperature, taking into account the outside temperature and type of system. The type of curve should be selected in correspondence with the projected temperature of the system and the nature of the dispersions present in the structure. For high-temperature systems, one of the curves depicted below may be chosen. 1 82 45 35 20 1 Installation and servicing instructions / 47