AristonThermoUK
Views
9 months ago
Flag

Genus ONE+ WiFi Installation Manual

  • Text
  • Wwwaristoncom
  • Manual
  • Wifi
  • Genus
  • Maintenance
  • Efficiency
  • Appliance
  • Flue
  • Installation
  • Heating
  • Boiler
Ariston Genus ONE+ WiFi Installation and Servicing Manual

INSTALLATION Connecting

INSTALLATION Connecting the Flue Flue System The provision for satisfactory flue termination must be made as described in BS 5440-1:2008. The appliance must be installed so that the flue terminal is exposed to outdoor air. The terminal must not discharge into another room or space such as an outhouse or lean-to. It is important that the position of the terminal allows a free passage of air across it at all times. The terminal should be located with due regard for the damage or discolouration that might occur on buildings in the vicinity, it must also be located in a place not likely to cause nuisance. In cold or humid weather water vapour may condense on leaving the flue terminal. The effect of such “steaming” must be considered. If the terminal is less than 2 metres above a balcony, above ground or above a flat roof to which people have access, then a suitable stainless steel terminal guard must be fitted. The minimum acceptable spacing from the terminal to obstructions and ventilation openings are specified in Fig. 1. flues should not penetrate this area 600mm P Q Q 600mm 2000mm Q D, E N I B boundary J Fig. 1 F A C H H M K H L G I Location A Below an opening Fanned draught 300 B Above an opening 300 C Horizontally to an opening 300 D Below gutters, soil pipes or drain pipes 75 E Below eaves 200 F Below balcony or cart port roof 200 G From a vertcaldrainpipe or soil pipe 150 H From an internal or external corner, or to a boundary alongside the terminal 300 I Above ground, roof or balcony level 300 J From a surface or a boundary facing 600 the terminal K From a terminal facing the terminal 1200 L From an opening in the car port into the building 1200 M Vertically from a terminal on the same wall 1500 N Horizontally from a terminal on the same wall 300 P From a structure on the roof N/A Q Above the highest point of intersection with the roof Site in accordance with manufacturer’s instructions / 20 420011270900 - Rev. 04 - 072024

INSTALLATION Minimum Length = 500 mm 180 mm 150 mm Warning The exhaust gas ducts must not be in contact with or close to inflammable material and must not pass through building structures or walls made of inflammable material. When replacing an old appliance, the flue system must be changed. Important Ensure that the flue is not blocked. Ensure that the flue is supported and assembled in accordance with these instructions. 118 118 mm Fig. 2 Installation without extension Level 150 mm Installation with extension slope * pente Level 150 mm * Min slope: 1˚ 1˚= 17.5mm per metre Fig. 3 Installation and servicing instructions / 21

INSTALLATION MANUALS

AristonThermoUK
Views
9 months ago
Flag

Genus ONE+ WiFi Installation Manual

  • Text
  • Wwwaristoncom
  • Manual
  • Wifi
  • Genus
  • Maintenance
  • Efficiency
  • Appliance
  • Flue
  • Installation
  • Heating
  • Boiler
Ariston Genus ONE+ WiFi Installation and Servicing Manual

INSTALLATION Connecting

INSTALLATION Connecting the Flue Flue System The provision for satisfactory flue termination must be made as described in BS 5440-1:2008. The appliance must be installed so that the flue terminal is exposed to outdoor air. The terminal must not discharge into another room or space such as an outhouse or lean-to. It is important that the position of the terminal allows a free passage of air across it at all times. The terminal should be located with due regard for the damage or discolouration that might occur on buildings in the vicinity, it must also be located in a place not likely to cause nuisance. In cold or humid weather water vapour may condense on leaving the flue terminal. The effect of such “steaming” must be considered. If the terminal is less than 2 metres above a balcony, above ground or above a flat roof to which people have access, then a suitable stainless steel terminal guard must be fitted. The minimum acceptable spacing from the terminal to obstructions and ventilation openings are specified in Fig. 1. flues should not penetrate this area 600mm P Q Q 600mm 2000mm Q D, E N I B boundary J Fig. 1 F A C H H M K H L G I Location A Below an opening Fanned draught 300 B Above an opening 300 C Horizontally to an opening 300 D Below gutters, soil pipes or drain pipes 75 E Below eaves 200 F Below balcony or cart port roof 200 G From a vertcaldrainpipe or soil pipe 150 H From an internal or external corner, or to a boundary alongside the terminal 300 I Above ground, roof or balcony level 300 J From a surface or a boundary facing 600 the terminal K From a terminal facing the terminal 1200 L From an opening in the car port into the building 1200 M Vertically from a terminal on the same wall 1500 N Horizontally from a terminal on the same wall 300 P From a structure on the roof N/A Q Above the highest point of intersection with the roof Site in accordance with manufacturer’s instructions / 20 420011270900 - Rev. 04 - 072024

INSTALLATION Minimum Length = 500 mm 180 mm 150 mm Warning The exhaust gas ducts must not be in contact with or close to inflammable material and must not pass through building structures or walls made of inflammable material. When replacing an old appliance, the flue system must be changed. Important Ensure that the flue is not blocked. Ensure that the flue is supported and assembled in accordance with these instructions. 118 118 mm Fig. 2 Installation without extension Level 150 mm Installation with extension slope * pente Level 150 mm * Min slope: 1˚ 1˚= 17.5mm per metre Fig. 3 Installation and servicing instructions / 21

Search