Views
1 year ago

Genus ONE Net - User Manual

  • Text
  • Programming
  • Boiler
  • Heating
  • Display
  • Settings
  • Manual
  • Appliance
  • Ariston
  • Active
  • Auto
  • Genus

USER’S MANUAL DISPLAY

USER’S MANUAL DISPLAY Date and time 26/10/15 12:30 Keylock active D.H.W. set temperature and indication of 42° the set temperature level C.H. set temperature and indication of the set temperature level 26/10/15 12:30 10° 20,5° 3 00 02 04 06 08 10 12 14 16 18 20 22 24 60° 1,5 bar 82° COMFORT AUTO Riscaldamento attivo Initial operating procedures Check the water pressure on the pressure gauge and make sure that the figure is between 0.6 and1.5 bar when the system is cold. If the pressure is just under the minimum value the display will request a filling procedure - see note below. FILLING PROCEDURE RE-ESTABLISH THE CORRECT PRESSURE USING THE FILLING LOOP (POSITIONED UNDERNEATH THE BOILER) AND PRESS THE MODE BUTTON FOR 5 SECONDS. THE DISPLAY SHOWS “Air Purge Active“. WHEN THE PRESSURE GAUGE INDICATES A PRESSURE OF 1 BAR, CLOSE THE FILLING VALVE AND PRESS THE MODE BUTTON. THE DISPLAY RETURNS TO NORMAL VIEW. Re-establish the correct pressure by filling loop. If the pressure drops very frequently, there may be a water leak at some point in the system. If this is the case a plumber should be contacted. Warning scheduled maintenance Heating operation set Heating operation active D.H.W. operation set 1 2 D.H.W. operation active Flame detected with indication of power used Digital pressure gauge (bar) Scrolling text displaying operation as information Error wsignals The display show the code and description AUTO function activated Hot Water Comfort activated CH Schedule programming (set display: boiler base - see user’s menù) Central heating ALERT AUTO COMFORT Note. Connections viewed from behind boiler. Note: Connections viewed from behind boiler 1. To repressurise the system ensure flexible hose 3 is connected 2. Slowly open taps 1 & 2 (see diagrams above) 3. Water will be heard entering the system 4. When the pressure gauge reads 1.5 bar close taps 1 & 2 3 CH Schedule programming (set display: boiler complete - see user’s menù) Internal temperature displayed for set zone. (with bus device connected - optional) External temperature displayed ECO mode WIFI active WIFI connected to the local network, but without access to the server WIFI not configured Solar temperature probe connected - option 6 /

USER’S MANUAL Ignition procedure Press the ON/OFF button on the control panel to switch on the boiler. The display shows the initialisation procedure - indicated by the bar. Wi-Fi bo Initializing....... Once the procedure is completed, the display will visualise the temperatures set for the central heating and domestic hot water circuits (display configuration: boiler base). It’s also required to set the date, time and language - see the note below. 00/00/00 00:00 42° 1,5 bar 70° Operating mode selection Use the MODE button 4 to select the desired operating mode. Operating mode Winter heating + hot water production for domestic use with set temperature Summer only hot water production for domestic use with set temperature Display 19/11/15 09:49 42° 1,5 bar 70° 42° Press OK to enter Menu 19/11/15 09:50 Press OK to enter Menu 19/11/15 09:49 The ignition of the burner will be signalled by the blue LED 11. 1,5 bar 1,5 bar Press OK to enter Menu 70° Adjusting the heating It is possible to set the temperature of the heating water by pressing the buttons 9 +/-. The temperature that may be obtained which varies from 40°C to 82°C. The value set previously will flash on the display. Press OK to enter Menu Operating ATTENTION mode - Initial selection start-up The first time the display requires a few basic settings. First, select the language. Press the programming key b to select the language, then press the OK button to confirm. Move on to setting the date and time. Press the programming key b to make a selection, press the OK button to confirm your selection. Press the programming key b to set the value. Press the OK button to confirm. Save the settings by pressing OK. Press the OK button to access the User’s Menu. Press the programming key b to scroll through the menu list and select a parameter, then press OK to confirm. CAUTION!! Some parameters are protected with an access code (safety code) which protects the boiler settings from unauthorised use. 20/11/15 09:57 40° 1,5 bar 70° C Heating active Domestic hot water temperature adjustement It is possible to set the temperature of the domestic hot water by pressing the buttons 3 a temperature may be obtained which varies from 36°C to 60°C. The value set previously will flash on the display. 20/11/15 09:57 42° 1,5 bar 70° DHW active / 7