AristonThermoUK
Views
3 years ago
Flag

Genus HE 35 Plus Manual

123,5 200 25 107 Fig.

123,5 200 25 107 Fig. 11.14 ø 100 In the event that twin flue pipes are used, and the boiler has a side clearance of less than 60mm from the wall, it is necessary to cut a larger diameter hole for the flue pipe, this should be ø100 mm, this will then allow for easier assembly of the air intake elbow and the tube outside the wall (see Fig. 11.14). 60 mm Fig. 11.15 TABLE A Concentric outlet 60/100 Min length Max. length 35 kW 0.3 m 4 m Concentric outlet 80/125 Min length Max. length Length equivalency for 45 o elbow 90 o elbow 0.5 m 1 m TABLE B 35 kW 0.3 m 10 m 45 o elbow 90 o elbow 0.5 m 1 m Operating zone in separate 35 kW ducts ZONE DE FONCTIONNEMENT EN CONDUITS SEPARES 35 kW TABLE C Twin flue outlet 35 kW Flue gas length in metres / Longueur fumées mètre HORIZONTAL Horizontal 100 90 80 70 60 50 40 30 20 10 0 Operating zone ZONE DE FONCTIONNEMENT 0 10 20 30 40 50 60 70 80 90 Longueur Air length AIR in metres mètre 200 180 160 140 120 100 80 60 40 20 0 Flue gas length in metres / Longueur fumées mètre vertical VERTICAL For coaxial systems, the maximum development value, mentioned in the table above also takes into account an elbow. For twin flue systems the maximum development value, mentioned in the table includes the exhaust gas/air intake terminal. Type 5 outlets should respect the following instructions: 1- Use the same ø 80 mm flue pipes for the gas intakes and exhaust gas ducts. 2- If you need to insert elbows in the gas intake and exhaust gas ducts, you should consider for each one the equivalent length to be included in the calculation of developed length. 3- The exhaust gas duct should jut above the roof by at least 0.5 m. 4- The intake and exhaust gas ducts in Type 5 must be installed on the same wall, or where the exhaust is vertical and the air intake horizontal, the terminals must be on the same side of the building. 28

TYPE 1 TYPE 2 TYPE 3 TYPE 4 TYPE 5 FIG. 11.16 NOTE: DRAWINGS ARE INDICATIVE OF FLUEING OPTIONS ONLY. AIR INTAKE MUST NOT BE FITTED ABOVE THE EXHAUST AIR INTAKE EXHAUST AIR INTAKE FIG. 11.17 29

AristonThermoUK
Views
3 years ago
Flag

Genus HE 35 Plus Manual

123,5 200 25 107 Fig.

123,5 200 25 107 Fig. 11.14 ø 100 In the event that twin flue pipes are used, and the boiler has a side clearance of less than 60mm from the wall, it is necessary to cut a larger diameter hole for the flue pipe, this should be ø100 mm, this will then allow for easier assembly of the air intake elbow and the tube outside the wall (see Fig. 11.14). 60 mm Fig. 11.15 TABLE A Concentric outlet 60/100 Min length Max. length 35 kW 0.3 m 4 m Concentric outlet 80/125 Min length Max. length Length equivalency for 45 o elbow 90 o elbow 0.5 m 1 m TABLE B 35 kW 0.3 m 10 m 45 o elbow 90 o elbow 0.5 m 1 m Operating zone in separate 35 kW ducts ZONE DE FONCTIONNEMENT EN CONDUITS SEPARES 35 kW TABLE C Twin flue outlet 35 kW Flue gas length in metres / Longueur fumées mètre HORIZONTAL Horizontal 100 90 80 70 60 50 40 30 20 10 0 Operating zone ZONE DE FONCTIONNEMENT 0 10 20 30 40 50 60 70 80 90 Longueur Air length AIR in metres mètre 200 180 160 140 120 100 80 60 40 20 0 Flue gas length in metres / Longueur fumées mètre vertical VERTICAL For coaxial systems, the maximum development value, mentioned in the table above also takes into account an elbow. For twin flue systems the maximum development value, mentioned in the table includes the exhaust gas/air intake terminal. Type 5 outlets should respect the following instructions: 1- Use the same ø 80 mm flue pipes for the gas intakes and exhaust gas ducts. 2- If you need to insert elbows in the gas intake and exhaust gas ducts, you should consider for each one the equivalent length to be included in the calculation of developed length. 3- The exhaust gas duct should jut above the roof by at least 0.5 m. 4- The intake and exhaust gas ducts in Type 5 must be installed on the same wall, or where the exhaust is vertical and the air intake horizontal, the terminals must be on the same side of the building. 28

TYPE 1 TYPE 2 TYPE 3 TYPE 4 TYPE 5 FIG. 11.16 NOTE: DRAWINGS ARE INDICATIVE OF FLUEING OPTIONS ONLY. AIR INTAKE MUST NOT BE FITTED ABOVE THE EXHAUST AIR INTAKE EXHAUST AIR INTAKE FIG. 11.17 29

Search