settings - adjustment -
settings - adjustment - problem identification menus menu sub-menu Parameter Description value 8 6 STATISTICS 8 6 0 Number of hours burner operating in heater mode (xxh/10) 8 6 1 NOT PRESENT 8 6 2 Number of flame separations (nr/10) 8 6 3 Number of ignition cycles (nr/10) 8 6 4 NOT PRESENT 8 6 5 Average length of heating request (minutes) 8 7 E@SY HOTLINE NOT ACTIVE 8 7 0 8 7 1 8 8 ERROR LIST 8 8 0 10 last errors from E00 to E99 This parameter allows the last 10 boiler errors flagged to be displayed, indicating the day, month and year. When the parameter is accessed, the errors are displayed listed from E00 to E99. For each error, the following sequence is displayed: E00 - error number 108 - error code 8 8 1 Error list reset Reset OK = yes ESC = no default setting 48
maintenance Important Maintenance is an essential part of the safe and efficient operation of the boiler and ensures its durability. It should be performed according to the instructions given in current legislation. Perform combustion analysis regularly in order to check the operating efficiency of the boiler and to make sure any polluting substances released are within the boundaries set by current legislation. Before beginning maintenance work: - Disconnect the appliance from the electricity supply by turning the external bipolar switch to the “OFF” position; - Remove the fuse - Close the gas isolation valve. After the work has been completed the initial settings will be restored. General comments It is recommended that the following inspections be carried out on the boiler at least once a year: 1. Check the seals in the water part and, if necessary, replace the gaskets and restore the seal to perfect working order. 2. Check the seals in the gas part and, if necessary, replace the gaskets and restore the seal to perfect working order. 3. Visually check the overall condition of the boiler. 4. Visually check the combustion and, if necessary, disassemble and clean the burner. 5. Following the inspection detailed in point “3”, disassemble and clean the combustion chamber, if necessary. 6. Following the inspection detailed in point “4”, disassemble and clean the burner and injector, if necessary. 7. Cleaning the primary heat exchanger 8. Make sure the following heating safety devices are operating correctly: - temperature limit safety device. 9. Make sure that the following gas part safety devices are operating correctly: - absence of gas or flame safety device (ionisation). 10. Perform a general inspection of the boiler operation. 11. Remove oxide from the detection electrode using an emery cloth. 12. After servicing, complete the relevant Service Interval Record section of the Benchmark Checklist (page 62). 13. These checks are not exhaustive. Further mechanical, electrical, condensate and combustion maintenance checks may be required. 14. Clean and refill the condensate trap Operational test After having carried out the maintenance operations, fill the heating circuit at a pressure of approximately 1.5 bar and release the air from the system (scaled system only). - Begin operating the boiler. - If necessary, release the air from the heating system again. - Check the settings and make sure all the command, adjustment and monitoring parts are working correctly. - Check the flue system is sealed and operating correctly. Draining procedures The heating system must be drained using the following procedure: - Switch off the boiler, make sure the external bipolar switch is in the OFF position; - Open the system drain off cock and collect the escaping water in a container; - Empty the water from the lowest points of the system (where applicable). If the system is to be left inactive in areas where the room temperature may fall below 0°C during winter, we recommend that anti-freeze liquid is added to the water in the heating system in order to avoid the need for repeated draining; when this liquid is used make sure it is compatible with the stainless steel used for the bodywork of the boiler. We recommend the use of anti-freeze products which contain PROPYLENE GLYCOLS as these inhibit corrosion and that they are used in conjunction with the antiscaling and anti-corrosion function, in the quantities suggested by the manufacturer, at the mimimum temperature. Regularly check the pH level of the water/anti-freeze mix in the boiler circuit and replace it when the value measured is lower than the limit prescribed by the manufacturer. DO NOT MIX DIFFERENT TYPES OF ANTI-FREEZE. The manufacturer will not be held liable for any damage caused by the appliance or the system due to the use of inappropriate anti-freeze substances or additives. WARNING Before handling, empty all components which may contain hot water, performing bleeding where necessary. Descale the components in accordance with the instructions provided on the safety data leaflet supplied with the product used, make sure the room is well ventilated, wear protective clothing, avoid mixing different products, and protect the appliance and surrounding objects. Seal all openings used to take a gas pressure reading or to make any gas adjustments. Make sure that the nozzle is compatible with the supplied gas. If a smell of burning is detected or smoke is seen leaking from the appliance, or there is a smell of gas, disconnect it from the electricity supply, shut off the gas valve, open the windows and call for technical assistance. Cleaning the condensate trap The trap is accessed by emptying the condensate bowl located in the bottom section. Wash with water and detergent. Replace the condensate collection bowl in its housing. NB: In the event of prolonged use of the appliance, the trap must be filled before being used again. A lack of water in the siphon is dangerous and may cause exhaust gases to be released into the atmosphere. 49
X